Putting Off Repairs Until After the Holidays? Why It Could Cost Your Fleet More in 2027

Every December, fleets fall back on the same line: “we’ll deal with it in January.” The budget is almost gone, the shop is short a few mechanics, and a repair that doesn’t keep the truck off the road can surely wait a few weeks.

This year, waiting is likely to cost more than usual. Parts prices have climbed a lot in just a few years, some categories jumped more than 15% in twelve months, and tariffs on trucks and parts are set to change again on January 1, on both sides of the border. The point isn’t to do everything before the holidays. It’s to know what to fix now, what to order now, and what can safely wait.

Why year-end pushes everything to January

Trucking doesn’t take the holidays off. Trucks keep rolling, customers still expect their loads, and the shop stays open. But with the holidays, you have fewer mechanics on the floor right when you need every truck on the road. Add a manager who’s out and has to sign off on a repair, and a two-hour job can drag on for a week.

That’s usually how the backlog grows in December, without anyone actually deciding it should.

What the numbers say

Maintenance keeps getting more expensive

Since 2019, combined truck parts and labor costs have climbed 27.4%, according to the benchmark report from Decisiv and TMC. Parts are up 23.8%, labor 33.5%.

The American Transportation Research Institute (ATRI) sees the same thing: in 2025, repair and maintenance averaged US$0.22 per mile, 8.6% more than the year before.

Some parts jumped sharply

In Q4 2025, average parts prices were up 3.7% year over year. That average hides some big gaps. If your shop goes through a lot of axle components or bearings, you’ve probably already seen it on your invoices:

Parts categoryYear-over-year increase (Q4 2025)
Rear axle components+20.6%
Wheels, rims, hubs and bearings+15.5%
Multi-piece filter kits+11.9%

Source: Decisiv/TMC Parts & Labor Service Benchmark Report, Q4 2025 (March 2026).

To be clear, costs did slow down in early 2026. In Q1, combined parts and labor were even slightly down year over year (-0.8%), before turning back up in Q2 (+1.1%). A pause, not a reversal.

Tariffs are muddying the picture

Two dates matter for every fleet:

  • November 1, 2025: the US put a 25% Section 232 tariff on imported medium and heavy-duty trucks and a range of parts (engines, transmissions, axles, chassis and more). For products that comply with USMCA (CUSMA in Canada), only the non-US content is taxed. A lot of North American parts move through US supply chains, so that cost can show up in prices on both sides of the border.
  • January 1, 2027: US tariffs on Canadian trucks and auto parts are set to go from 25% to 50%, based on a presidential announcement on August 24, 2026. As of early November, implementation rules still hadn’t been published, including how USMCA/CUSMA-compliant products will be treated.

Running a US fleet? Section 232 tariffs on imported steel and aluminum sit at 50%, which pushes up the cost of components made from those metals. And if you buy Canadian-built trucks or parts, the January 1 increase hits you directly.

Running a Canadian fleet? Since September 8, 2026, Canada has applied counter-tariffs on C$27.6 billion in US imports, including 50% on a range of steel and aluminum products. Truck parts aren’t targeted directly, but they’re made from those metals.

Nobody knows yet exactly how all of this will land in parts pricing. What we do know is that prices will be harder to predict and some parts could take longer to arrive.oad.

The real risk: the deferred repair that becomes a breakdown

Parts prices are only half the story. Worn brakes, a hot wheel bearing or a small leak left alone for six weeks doesn’t always stay a planned repair. It can end up on the shoulder in the middle of winter, with a tow, a truck out of service and a missed delivery.

When you plan a repair, you pick the timing, the part and the price. When the truck breaks down, you don’t get to pick anything.

How to triage your maintenance backlog before January 1

With a reduced crew, you won’t catch up on the whole backlog before the holidays, and you don’t need to. Sort every pending repair with two simple questions: what happens if I wait, and how much more will it cost me?

Priority 1: safety and compliance, right now

Brakes, steering, tires, lights, defects from pre-trip inspections (DVIRs), manufacturer recalls: anything that could put a unit out of service at a roadside inspection goes first. These can’t wait, budget or not.

Priority 2: parts at risk of price increases, order now

Even if the repair happens in January, nothing stops you from ordering the part before January 1. Focus on:

  • the categories that have gone up the most (axles, wheels, hubs, bearings, filters);
  • imported parts or parts with long lead times;
  • the filters and consumables your preventive maintenance program will need in Q1.

If some of your parts come from Asia, keep Lunar New Year in mind too: February 6, 2027. Production and shipping often slow down around that date.

Priority 3: preventive maintenance that’s due, get it on the schedule

Units that have hit or passed their mileage or engine-hour interval need a shop date. Start with spares or trucks that run less in December, and rotate them through based on which mechanics are available.

Priority 4: the rest can wait

Body work, interior, non-critical upgrades: this is where putting things off costs you next to nothing.

Three decisions to make before January 1

Set an approval threshold for the holidays. For example, any repair under a set dollar amount can be approved by the shop lead without waiting for a manager who’s out. A truck waiting three days on a signature in December is one less truck on the road at the worst possible time.

Negotiate your 2027 pricing now. Call your parts suppliers and outside shops before January to lock in prices or labor rates.

Look at the history on your older trucks. Before putting money into a major repair, check what that unit has cost you in maintenance so far. Sometimes the right call is to replace it.

The role of your fleet maintenance software

This kind of triage is hard when your backlog is spread across emails, spreadsheets and your shop foreman’s memory. Fleet maintenance software (CMMS) like MIR-RT puts it all in one place:

Want to see your whole maintenance backlog at a glance? Request a MIR-RT demo.

Frequently Asked Questions

Is it a bad idea to defer fleet maintenance?

Not always. Deferring a cosmetic or low-risk repair is reasonable. Deferring a safety-related repair, an inspection defect or preventive maintenance that’s due increases the risk of a breakdown and, with rising costs and tariff uncertainty, could cost more in 2027.

Why are heavy-duty truck parts prices going up?

Truck parts costs have risen 23.8% since 2019, according to Decisiv and TMC. On top of that trend come 25% US tariffs on imported trucks and key heavy-duty parts since November 2025, higher tariffs on steel and aluminum in both the US and Canada, and a US tariff increase on Canadian trucks and parts announced for January 1, 2027.

Which repairs should never be deferred?

Anything related to safety and compliance: brakes, steering, tires, lights, defects reported on pre-trip inspections and manufacturer recalls.

Should I order parts before January 1, 2027?

For parts at risk of price increases, with long lead times, or that you’ll need in Q1, ordering before January 1 can protect you from an increase. Check your inventory first to avoid duplicates.

Recent posts

Your vendor was acquired, costs are rising, support is slowing down or your maintenance software no longer keeps up with your operations: here are 5 signs it may be time to switch CMMS software, plus a CMMS migration checklist.
Discover how the integration between MIR-RT and Hunter Engineering Company automates the transfer of tire and wheel alignment inspection results to improve maintenance tracking and planning.
Your vendor was acquired, costs are rising, support is slowing down or your maintenance software no longer keeps up with your operations: here are 5 signs it may be time to switch CMMS software, plus a CMMS migration checklist.
Discover how the integration between MIR-RT and FOCUS by TELUS automates telematics data transfers, improves unit tracking and simplifies driver vehicle inspections and preventive maintenance planning.
DataDis launches its telematics integration with Platform Science: real time geofencing, odometer and engine hour data automatically transferred into MIR-RT to optimize your fleet's preventive maintenance.
Discover how the integration between MIR-RT and Sage BusinessVision automates accounting data transfers to simplify financial management and improve operational visibility.

Get more information